Sheila's Quilt Party 2024 is open for enrollment!

Binding 101 - Part Five - the final step

Hi and welcome to Binding 101, the final step.

Don't you love it when you get to the end of a project and know that all the hard work you have put in is finally done, and you can move guilt-free onto the next one?

Once I have my binding sewn down by machine I look forward to spending the evening quietly contemplating the enjoyment of the project, and anticipating the next, while sewing down my binding.

Love it or hate it, hand sewing does make for a lovely finish, and hopefully with these tips you will find it enjoyable.

To start off, I press my binding back.

IMG_4149
Press the binding back from the face of the quilt

This is what the corners will look like

IMG_4150

Fold the binding over to the back of the quilt.

Use a fine needle to sew down your binding, this makes it easier to achieve an invisible stitch.

I use a fine applique needle #12 (Clover or Bohin brands are what I have available). These are easy to thread with the Clover desktop needle threader.

IMG_4157

I am using Aurifil #50 cotton in Dove...

Continue Reading...

Binding 101 - Part Four - Easy mitred join (no rulers!)

Welcome to part four of my Binding 101 tutorial.

Joining the ends of my binding was always a bit of a hit and miss affair. I used to fold one end inside the other and hope for the best. This didn't look good as it produced a lumpy, straight join when all the others were mitred and nice and flat.

I tried using various binding gadgets but could never figure out from one quilt to the next what to do, and got frustrated when I cut too much off, or cut the wrong way round.

Then one day I decided the only thing to do was to try and figure it out for myself, and I eventually came up with this method which for me is more intuitive and I can now actually remember how to do it every time!


Get a beautiful join in your binding

Give it a try next time you join your binding...

Start by leaving yourself PLENTY of room to work with. I start sewing my binding 10-12" from the beginning of the strip, and leave a good 12" gap at the end. The orange pins in this photo show where I started and stopped...

Continue Reading...

Binding 101 - Part Three - Mitred Corners

Welcome to my binding tutorial. If you haven't done so yet, make sure you read parts one and two before moving on to this step.

Ok, so now we have reached a corner.

Take your quilt over to the ironing board.

Take the binding strip and fold it out to the right, making a 45 degree angle like this and press:

 

IMG_4118
Fold binding to the right

 

Keeping this fold in, fold over to the left and press.

IMG_4119
Fold back over to the left

 

Continue sewing from the top edge of the quilt.

IMG_4120
Start sewing again from the top

Carry on all the way around, repeating this method for each of the corners.

This is what the corners will look like from the front:

IMG_4150

Once you reach the final side, stop sewing at least 12" from where you started. Don't cut off any of the binding strip yet, we will use it in the next step when we make the mitred join.

IMG_4125
The orange pins show where I started and stopped sewing

Join me next for part four - my mitred join technique.

 
Continue Reading...

Binding 101 - Part Two - Attaching the binding to the quilt

Welcome to part two of my binding tutorial!

We are starting with the trimmed quilt and binding strip that we prepared in part one.

Now we are going to attach the binding to the front of the quilt by machine.

First you need to set up your needle position. I like to sew my binding on with just over 1/4" (about 5/16") allowance.

Use your ruler to work out where your needle needs to be. If you have a machine where you can adjust the needle position, this is easy.

If you can't adjust your needle, work out where you need the edge of the quilt to be as you are sewing. You can mark this with a bit of masking tape.

I use my walking foot when attaching the binding.

IMG_4107
Set up your needle position between 1/4" and 3/8"

 

Now lay the binding on top of the quilt with the raw edges together.

Make sure you leave a really generous allowance of binding free - at least 10" for joining at the end.

Start sewing your binding about halfway down one side of the quilt. Stitch length about 2-2.5mm.

...

Continue Reading...

BINDING 101 STEP 1

Here is part one of my step by step binding tutorial.

I always find this the hardest part of writing instructions and patterns, so I decided to take step by step photos as I did the binding on the Modern Triangle Sampler. There are many different approaches to binding but this is the method I have tweaked over the years to suit me.

Binding 101

  IMG_4169

Part One - Trimming your quilt

Once the quilting is complete, trim your quilt. If there is a handy seam close to the edge, I use a ruler and measure from this seam to the outside so that I can keep this distance the same. Cut with a rotary cutter. Here I can see that if I use the 4 1/8" line on this border, I can trim the outside edge close enough so I won't see any batting when I sew on my binding.

IMG_4103
Line the ruler against the border seam and trim

When you get to a corner, use the ruler to keep everything square. Square corners will be your friend!

 

2. Preparing the binding strips

First you need to work out how many strips you...

Continue Reading...
Close

50% Complete

Sign up to my email list

Enter your details here